Skill Level: Intermediate

If you want to level a steep slope on your property or enclose an area for a decorative garden, a concrete block retaining wall might be just what your landscape needs. With a little effort, you can add a beautifully landscaped area that is easy to maintain. There are retaining wall systems designed specifically for the purpose, created with the do-it-yourselfer in mind. The finished product looks complicated, but the project is quite simple, requiring only basic tools. Lowe's is happy to provide this information as a service to you.

Tools & Materials

Tools

• Chisel
• 3 lb. drilling hammer
• Carpenter's level
• Mason's line
• Line level
• Flat-pointed shovel
• Hand tamper
• Gloves
• Safety glasses
• Back support

Materials

• Retaining wall blocks
• Porous landscape fabric
• Gravel (optional)
• Leveling sand
• Wood stakes

Take Control of Your Yard

These concrete blocks interlock and require no mortar. Aside from the weight, they are almost as easy to assemble as children's interlocking blocks. If you make mistakes or change your mind about the location or shape of your wall, just dismantle it and start over.
Since these systems use no mortar or rebar reinforcement system, they are more appropriate for terraces with low walls than those with tall walls. Using a system of terraces, you can create a pleasant, stepped slope that is safer than a single, tall wall. A system of terraces also gives you many planting and landscaping opportunities.

How These Block Systems Work
Retaining wall blocks in mortarless systems have a lip on the bottom rear side to lock the blocks together and create a step effect. When the cavity behind the wall is filled with soil, the blocks are pushed forward, strengthening the joints between the lips and the underlying blocks. The blocks are tapered from the front face to the rear to allow easy formation of curves.

Note: Mortarless wall block is intended for construction of relatively low walls. Taller walls can be constructed but further consideration must be given to drainage, reinforcement and stability. Recommended dry-fit heights vary by product but for general reference, consider 15" - 28" as a guide for planning purposes. Consult the manufacturer's instructions concerning height limits or recommendations made by the manufacturer.

Helpful Tips Before You Get Started

• When figuring how many blocks you'll need for your wall, remember that they are basically one foot long. Also note that curves require more blocks than straight runs.
• When the blocks are delivered, do not have the pallets set on your driveway because they are extremely heavy and can cause damage.
• To accurately cut a block, score a line around it with a 3 1/2" brick chisel and a 3 lb. sledgehammer. Place the cutting edge of the chisel in the center of the score line and strike the chisel sharply with the sledgehammer.
• After you dig the trench for the wall, use leveling sand or paver base as a foundation for the first course. The sand allows block to be levelled more easily and accurately.

Dig the Trench
The key to successful retaining wall construction is a level foundation course of block. The foundation course must be below ground level so that the soil will hold it firmly in place.

1. Measure out your prospective wall, using stakes and string to mark off the key points, or use a garden hose to mark off its perimeter.
2. Starting at the lowest point, use a flat-pointed shovel to dig a trench for the foundation course. The dimensions of the trench will vary depending on the size of your block — generally about 4" deep. The foundation course should be below ground level.
3. Tamp the trench with a hand tamper to compact the underlying soil. Add a layer of leveling sand or paver base (1-2 inches) and tamp.

If your property slopes, you may have to dig your foundation trench in a series of steps equal to the height of the blocks. Then, as you continue with construction, build up the lower sections with block until the stepped areas accept successive courses of blocks in a level and seamless wall.

Lay The Courses
Once you have a sound foundation trench, you can begin laying your block. Regularly check for level as you build each course.

1. Set the first block in place. Check for level. If the block isn't level, tap it with the butt end of your hammer to adjust it.
2. If your property is relatively flat, continue laying the foundation course, making sure that all blocks are level with each other and below ground. If not, use the stepped approach mentioned above.
3. After the entire foundation course is installed, set one block in position at each end of the foundation course. The lip of each block should fit against the back of the foundation course block. Use a pair of line blocks and a line level to make sure that the first and last blocks are level with each other. If they are not, adjust the retaining wall blocks until the foundation course is completely level.
4. Cut one block in half for the start of the second course. This will ensure that the first and second courses are staggered. Set the rest of the second course blocks in place and then fill the trench around the foundation course with soil. Continue placing the blocks, making sure each course is staggered over the previous one.

Fill the Cavity

To prevent the soil from seeping through the spaces between the blocks, line the cavity behind the wall with porous landscape fabric.

1. Start at the base of the cavity and unroll the fabric until it overlaps the top course of block. Cut the fabric and continue along the length of the wall until the entire cavity is lined.
2. Fill the cavity. If the wall is 2 1/2' or higher, fill the area closest to the block with gravel. You should have gravel to a width of about 6" from the block. The rest of the cavity can be filled with soil. This will facilitate drainage.
3. Trim the excess landscape fabric. You can top off the terraces with decorative stone or mulch.